Log Entries For Rear Fuselage

Date	Summary
Aug 7, 2011	Rivet top skin
Aug 1, 2011	fastened tail cone top skin
Jul 24, 2011	Bolted the VS to bulkhead 5
Jul 24, 2011	Attached Vertical Stabilizer
Apr 4, 2011	Connected trim servo
Mar 25, 2011	spiral wrap and cable clamp wire runs
Mar 20, 2011	Debur tail cone
Jan 21, 2011	completed 330 drilling
Jan 18, 2011	Drilling top skin
Jan 15, 2011	Auto pilot pitch servo mount
Jan 14, 2011	Tail cone top skin
Jan 9, 2011	misc wiring tasks
Jan 4, 2011	Seat belt cattach and gusset
Jan 2, 2011	Tail cone top skin
Jan 1, 2011	Static lines
Nov 3, 2010	stiffeners riveted to top skins
Nov 1, 2010	Tail cone top skins
Oct 24, 2010	Static line
Oct 18, 2010	Trial fit foot steps
Oct 17, 2010	completed riveting side skins to belly skin
Oct 7, 2010	Aft push pull tube
Oct 5, 2010	completed riveting bulkhead5 and closeout
Oct 4, 2010	riveted side skins
Sep 29, 2010	final drill and debur closeout
Sep 27, 2010	match drilled closeout skin
Sep 21, 2010	final instal of bulkhead 5 and trial fit trim servo
Sep 20, 2010	Riveting top bulkheads
Sep 16, 2010	test fit vertical stabilator
Sep 12, 2010	completed drilling longerons and baggage closeout nut plates
Sep 11, 2010	Tailcone longerons
Sep 8, 2010	riveted bulkhead 1 assy
Sep 6, 2010	bulkhead nut plates
Sep 4, 2010	Installed nut plates lower #1 bulkhead
Sep 3, 2010	riveted side corner stiffener
Aug 30, 2010	riveted bell crank assy to belly skin
Aug 29, 2010	bellcrank assy and side skins
Aug 20, 2010	rivet stiffeners to belly skin
Aug 16, 2010	Bulkhead 4 pulleys
Aug 14, 2010	trimmed bellcrank bushings to final size
Aug 11, 2010	Bell crank and pulley Trial assembly
Aug 8, 2010	stabilator bell crank and bulkhead#1
Aug 6, 2010	bulkhead #1
Aug 4, 2010	riveted stiffeners to closeout skin
Aug 3, 2010	prep close out skin
Aug 1, 2010	close out skin
Jul 31, 2010	riveted bulkheads
Jul 30, 2010	top bulkheads 2&3
Jul 29, 2010	riveted bulkhead 4 assy
Jul 27, 2010	Bulkhead 4
Jul 25, 2010	Bulkhead 5 riveted and side skins fitted to belly skin
Jul 23, 2010	Bulkhead 5
Jul 18, 2010	riveted side wall gusset
Jul 16, 2010	Side skin aft assy
Jul 15, 2010	Bulkhead 5 and drilled corner stiffener
Jul 4, 2010	Bellcrank channel and belly skin stiffeners
Jul 3, 2010	Access panel rings and nutplates
Jun 29, 2010	belly skin and stiffeners
Jun 28, 2010	fitted side skin bulkheads and stiffeners
Jun 16, 2010	left side skin formed
Jun 13, 2010	Tail cone rt side formed
May 26, 2010	tailcone aft assy, bellcrank channel, and bulkheads
May 26, 2010	tailcone aft assy, bellcrank channel, and bulkheads
Apr 18, 2010	removed protective plastic
Apr 4, 2010	ready to form side skins
Apr 2, 2010	Started tailcone assembly

ExperCraft is supported by these quality vendors: